The refrigerator’s main control board controls the voltage being sent to the ice maker. If the control board is defective, the ice maker may not work at all. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to determine if Kenmore Ice Maker Not Working after reviewing the refrigerator’s wiring diagram.
A Kenmore fridge is a high-quality appliance. Still, it’s only enjoyable if all its functions are working correctly, especially its icemaker. Keep reading as this guide shines a light on why your samsung ice maker not making ice isn’t working as it should and what you can do to solve the problem.
If the Kenmore ice maker is not working, then a little investigating and troubleshooting may be able to alleviate the issue. From an ejector arm that refuses to budge to a kink in the water lines that run behind the fridge, there are a few reasons that can prevent ice from dropping out of the Kenmore Elite’s dispenser.
If you are facing Kenmore Ice Maker Not Working, then there are a few possible problems at hand. But before you decide your ice maker is defective, let’s take a look at some of the issues that can cause ice not to dispense. You might not need to get a new one yet.
Historically, ice makers built into refrigerators lasted the average life of the refrigerator. But now, manufacturers are adding more features to the ice makers, which decreases their lifespan to about five years.
Kenmore Fridge Not Making Ice: Common Causes And Solutions
There are three most likely reasons why your Kenmore Ice Maker Not Working: a failed water inlet valve, clogged water filter, or faulty ice maker. Let’s take a closer look at each one and how you can fix them.
1. Faulty Water Inlet Valve
The water inlet valve opens to supply water to the dispenser and ice maker. If it malfunctions, or if there is insufficient pressure, it will not be able to provide water to either of them. As a result, the ice maker will not produce ice.
If your valve solenoids are having mechanical or electrical problems, your valve won’t open water to the ice maker. A mechanical failure can be caused by mineral deposits building up and preventing the valve from opening. An electrical failure might be caused by burnt coils on the valve.
Keep in mind that the valve needs 20 psi to work. To test this, you need to measure the water pressure. If it’s at least 20 psi, check to see if there is electricity going to the water inlet valve. If the water inlet valve has power and is getting more than 20 psi of water pressure, but the Kenmore ice maker still won’t fill with water, chances are you need to replace the water inlet valve.
2. Wrong Temperature Setting
The ice maker won’t make cubes if the freezer is too warm. The temperature should be at -5 degrees Fahrenheit (-18 degrees Celsius), or lower.
If your freezer is staying above 15 degrees Fahrenheit or -9 degrees Kenmore Ice Maker Not Working, something might be wrong with the appliance. Debris on the coils might be keeping the appliance from properly cooling.
3. Frozen Evaporator Coils
When the refrigeration Evaporator coils are frosted, it means there is a defect in the defrost system. There are four possible causes of this failure: the defrost thermostat, control board, heater, or cold temp sensor.
The evaporator fan motor fails to properly circulate the air inside your freezer, or frosted evaporator coils restrict airflow, causing your ice maker to malfunction.
An ice maker’s inability to work correctly might be due to an evaporator motor that is not working or frozen evaporator coils. This will cause the temperature of the freezer to increase, which in turn will cause the ice maker to stop functioning properly.
4. Broken Door Switch
The door switch is what turns the ice and water dispenser off when the Kenmore Ice Maker Not Working is open. If the switch fails, it won’t turn on even if you push the buttons.
Checking the freezer door switch is easy. All you need to do is push it, and if the light goes off, that means the switch is working. If the light stays on, then there’s a malfunction with the switch.
5. Low Water Pressure
A water inlet valve needs about 20 psi of water pressure per square inch to work correctly. This means that if you turn off the water supply, disconnect the supply line from the inlet valve and hold the line over a bucket, you can see for yourself if the line has enough pressure to operate properly.
It sounds like the water is not flowing the way it’s supposed to. Let’s turn the water supply on and see if we can guess what the problem is. If there is a low flow of water, it may be an issue with the pipes or valves.